![woodpecker 3.2 grbl board min z switch woodpecker 3.2 grbl board min z switch](https://forum.mysensors.org/assets/uploads/files/1516838911455-613075bd-af72-4a92-8663-eb4012fe714a-image-resized.png)
The service life can be up to 10,000 hours.Įxcellent Heat Dissipation: Equipped with a large aluminum heatsink and cooling fan, this can help the heat dissipate fast and ensure the laser module works continuously.
#Woodpecker 3.2 grbl board min z switch full#
Longer Service Life: The fixed focus laser module can work at full power for 8 hours without any light decay.
![woodpecker 3.2 grbl board min z switch woodpecker 3.2 grbl board min z switch](http://www.bogdanberg.com/wp-content/uploads/2018/08/20180820_135610.jpg)
At the same power, the fixed focus laser module can cut 3mm linden wood in one pass, not possible with current adjustable laser modules. Compared with the adjustable focus laser module, the light spot of the fixed focus laser module is smaller.
![woodpecker 3.2 grbl board min z switch woodpecker 3.2 grbl board min z switch](https://content.instructables.com/ORIG/FD0/CYLF/JQUU2GZD/FD0CYLFJQUU2GZD.jpg)
This module is only compatible with 3018-MX3/3018-PROVer, but not compatible with 1810-PRO/3018/3018-PRO.įixed Focus: The fixed focus distance is 20mm. Desired patterns can be made easily on the wood or plastic by this unit. $132 = 85.000 (Z-axis maximum travel, millimeters)Application: The laser module is ideal for engraving, cutting, scribing, and drilling. $131 = 200.000 (Y-axis maximum travel, millimeters) $130 = 300.000 (X-axis maximum travel, millimeters) $27 = 1.000 (Homing switch pull-off distance, millimeters) $26 = 250 (Homing switch debounce delay, milliseconds) $25 = 500.000 (Homing search seek rate, mm/min) $24 = 25.000 (Homing locate feed rate, mm/min) $11 = 0.010 (Junction deviation, millimeters) Then play with the direction buttons and listen for any noise produced by the steppers etc.ĭo you have anyone else you can call upon for help in any way that may be a little more experienced ? Manually dial in the steppers so they are about half way across each lead screw. If you see the longer message then that's the best sign as it means the program can not only see the board but fully communicate with it too. When shutting down these types of program always do a disconnect first as just closing can on occasion leave the COM port a little stuck in limbo. Should be similar to below but some numbers may be different and that would be normal as I changed a lot of my parameters. You might want to expand the lower console a little upwards into the display area in case you missed it.
![woodpecker 3.2 grbl board min z switch woodpecker 3.2 grbl board min z switch](https://forum.mysensors.org/assets/uploads/files/1519090545209-finalcnchw.jpg)
OK thats a good start but There is usually a longer message that follows. I don’t know either is an GRBL 0.9 or 1.1… it doesn’t say anything on the board or i can’t find it… This report would have more information with System wide configuration file is “C:\Users\user\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino14/etc/nf”Īvrdude: stk500_recv(): programmer is not respondingĪvrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xfcĪvrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xfcĪvrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xfcĪvrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xfcĪvrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xfcĪvrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xfcĪvrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xfcĪvrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xfcĪvrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xfcĪvrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xfc Maximum is 2048 bytes.Ĭ:\Users\user\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino14/bin/avrdude -CC:\Users\user\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino14/etc/nf -v -patmega328p -carduino -PCOM4 -b115200 -D -Uflash:w:C:\Users\user\AppData\Local\Temp\arduino_build_936294/:i Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Sketch uses 930 bytes (2%) of program storage space. Here are the error massage it got from arduino IDE,Īrduino: 1.8.9 (Windows 10), Board: “Arduino/Genuino Uno”